If you are like most small business owners, you use the services of large delivery companies for most of your small business shipping needs. These services from larger delivery companies are ideal for national and international shipping needs, but you may also use courier services for local deliveries. Courier services often provide you with a reliable, cost-effective option, and many couriers offer personalized service and can specially-handle your package as needed. It is common for small business owners to compare rates of courier services before contracting with a courier for local delivery service. In your comparison, you may wonder what factors impact delivery rates. Identifying the most significant factors that influence these rates may help you to discover new ways to save on this service.

The Delivery Address
One of the most common factors that impacts courier Toronto rates is the delivery address. If your address is in the same city as the pickup location, you may expect to pay a more affordable rate. This is particularly true if the pickup and delivery addresses are in the prime service area that the courier works in. Some couriers will work outside of their prime service area for an additional fee. With this in mind, you can save money on courier fees if you find a courier that works in both your pickup and delivery locations.

Miles Traveled
Another factor that will affect the price you pay for courier services is the distance between the two locations. Your courier will incur a cost for each mile traveled in the form of fuel expense as well as wear and tear on the vehicle. You may consider mapping the distance between the two locations yourself to ensure that the mileage expense that you are being charged is for the fastest route between the two points.

Time Required for the Delivery
The delivery time will also affect your courier rate, and delivery times can vary based on traffic at the time you schedule the pickup, construction on the fastest route between the two points, weather conditions and more. Consider paying attention to the average hourly rate the courier charges for delivery service, and compare this rate against other couriers’ rates to identify cost savings through other sources.

Hiring a courier to deliver your package to a local area is a great option that can ultimately save you money. However, the cost of delivery services can add up over the course of a year, and you may be wondering how you can save money on delivery charges. By learning more about the factors that affect rates charged by couriers, you can more easily adjust or manage those factors to your benefit.

Jordan

The construction business is one of the fastest growing industries in Canada. Therefore, steel construction products are in high demand leading to the emergence of different types of steel suppliers. It’s a good trend, economically speaking, but can be confusing to a common citizen looking to purchase some steel products for construction. Some of the most common steel construction products are stainless steel corner guards, steel beams, pipe, and steel bars.

The confusion could stem from the measurements, units of measurement, and where to purchase. In terms of measurement, there’s always a lot of confusion vis-à-vis weights, thickness, gauges, and gauge numbers. MSG (Manufacturers Standard Gauge for Steel Sheets) is the widely used gauge system in Canada. The gauge system was developed with a fixed thickness for each corresponding gauge number.

Different Types of Steel Products

Steel corner guards are used to polish sharp edges in a building. They are sheared in factories and are made from stainless steel. Steel pipes are used in construction to convey fluids (liquids and gases). Steel bars are used to reinforce concrete while steel beams are attached by joists to the ceiling and floor to provide structural support for the walls.

The Most Common Units of Measurements

Even the most common units of measurements in the steel business come in numerous variations. Because steel as a construction tool has been around for quite a long time, several terms are uniquely used in the steel business; sometimes interchangeably to refer to different things. The mostly used steel measurement units in Canada are Pounds (LBS), CWT or hundredweight, and metric tonnes.

Where to Buy

All the different steel products used in Canada are acquired through several types of steel suppliers. There are quite a few options when it comes to buying steel products in the country. Take a look:

Mills

Steel mills are large organizations and buying steel directly from them is not always a good idea. They do not offer many size ranges and often want to ship in bulk. Buying directly from a mill eliminates the need for a middleman.

Service Centres

Service centres are usually smaller than milling companies. Service centres cut steel into small coils and sheets for industrial use. They act as the distribution centres since mills don’t want to hold inventory or ship in small volumes.

Traders and Brokers

Traders or brokers are your best option if you want to import steel from another country. They negotiate with the steel supplier on your behalf and can handle the import process for you. Foreign steel can be significantly cheaper than domestic steel. The only downside is that you will be dealing with a middleman and you’ll have no control of the quality of steel materials you receive. For more insights, BOSS Steel Limited has resources and information available on their website.

Jordan

Those who enjoy working on projects or performing repairs around the house likely have plenty of tools at their disposal. Unfortunately, the tools can often get lost due to a lack of organization in the garage. To ensure that your tools are easy to find, there are a few important tips to follow.

Hang the Tools on Pegboard

Pegboard is an effective product to hang on the walls of your garage to hang your power tools and make them easy to find. Group like items together on the wall to make them visible in the garage and within reach of your work area. You can also organize the items according to their size to make the space aesthetically pleasing.

Use a Professional Tilt Cart

Tilt carts are the perfect solution for those who need certain items on hand when they’re restoring a car or are building shelves. The cart can roll around the garage, making it easy to take with you and keep the essentials close by. The interior of the cart features multiple shelves that are adjustable with a pegboard panel where you can hang Dewalt tools and find them in seconds.

Hang a Magnetic Storage Panel

Magnetic storage panels are effective at hanging screwdrivers, wrenches, and nails in an area that features multiple panels. The product is constructed out of magnetized steel and is strong enough to hold a cast iron plate. Use the panel on the wall above your work bench to find specific items without digging through your drawers.

Add a Wire Spool Holder

A wire spoon holder will make it easy to keep your wire spools together to prevent them from becoming tangled. The product can be purchased or made yourself and will make it easy to keep all of your wire together in one place.

Use Component Drawers

Those who own power tools or basic products likely have plenty of small parts lying around, which can become disorganized and difficult to find. Use component drawers to store tiny parts and group them together. Label each drawer to make them easy to find and organize the parts every few months to ensure that you avoid creating junk drawers that can easily accumulate.

Hang Milk Crates

Milk crates can be used to store your Dewalt tools or your tape in a place that is easy to access and offers plenty of visibility for the products you use frequently. You can also stack the milk crates to make use of vertical space in your garage and limit the amount of items that sit on a table where you work frequently. Additional resources are available at the Mississauga Hardware website.

Jordan

The sheet Metal fabrication process is the basis of low cost fabrication and this is among the most common raw materials in manufacturing. Smaller amounts of material are used when comparing it with parts that are machined from block material. Parts that are made from block material can often times be redesigned in order to be adapted to sheet metal form. If they stack sheets of the same shape they can render a higher thickness. If they stack sheets of different shapes they build a 3D shape. When combining the metal fabrication process with other processes like milling a recess on a laser cut sheet the achieve more flexibility.

Sheet metal is used in industrial and non-industrial applications which include fuselages, wings, appliances, boilers, and also for kitchen and office equipment.

Metal fabrication shops make parts using methods such as bending, counter sinking, laser cutting milling,and Photochemical Milling just to name a few.

Jobs that require sheet metal fabrication generally start with shop drawings which include precise measurement then the go on to the fabrication stage.

To explain the processes of sheet metal fabrication we start with cutting, this is accomplished by sawing, shearing or chiseling with manual and power machinery.

Bending is done by manual or power driven methods. They use press brakes to air bend sheet metal into a form. Software programs make the press brakes very efficient and seamless.

The joining of pieces or the assembling process is done either by binding with an adhesive, welding,threaded fasteners or riveting.

Structural steel and sheet metal are the starting materials for fabricators. The raw materials that are used are, expanded metal, plate metal, welding wire and rods and casting.

Sheet metal roofing goes through a roll-former which is a machine that will turn metal coil into sheet metal roofing panels. These machines can be fitted with, manual or mechanized shears, and a computer controller unit for different panel profiles.

The basic process of making the sheet metal roofing panels is by feeding metal coil into the roll-former. When it is inside of the roll-former, the coil goes through a series of rolls that makes curves and bends. Each roll makes more of a bend than the previous one. The rolls in the former are made of stainless steel for durability. Some of these roll-former’s can bend metal as thick as 22 gauge.

The typical width of sheet metal roofing panels is 12, 16 and 20 inches. For the 12 inch panel they use a 16 inch coil. The extra 4 inches are used to make the locks on each side of the panel. For additional insights, please visit Heather & Little Limited – heatherandlittle.ca.

Jordan

The Workplace Hazardous Materials Information System (WHMIS) is Canada’s national hazardous chemical standard. The WHMIS labels are used to warn individuals of hazardous chemical dangers. The WHMIS classification helps workers handle, transport and store potentially dangerous chemicals.

“WHMIS Classification System”

The Department of Health Canada created the WHMIS Classification on October 31, 1988. The French variation is called the Systeme D’Information Sur Les Matieres Dangereuses Utilisees Au Travail (SIMDUT). These hazardous chemical safety labels are used on boxes, packages and containers to identify the contents thereof.

The WHMIS provide useful information on material safety data sheets (MSDS). Some workers might not have a chemistry background and these safety labels can help them handle these items without incident. The WHMIS uses the following classes for its materials:

A is Compressed Gas
B is Flammable & Combustible
C is Oxidizing
D is Poisonous & Infectious
E is Corrosive
F is Reactive

Class A Compressed Gas includes fire extinguishers, propane and chlorine. It is important to keep these at moderate temperatures and avoid punctures. Class B Flammable is propane and gasoline. Some chemicals, like propane, might have multiple class listings.

Class C Oxidizing includes oxygen, hydrogen peroxide and bleach. Workers should not store these next to combustibles, like wood or flammables.

The Class D Poisonous has three subgroups – D1, D2 and D3 – these could be fatal to humans via inhalation or ingestion. Class D1 includes hydrogen sulphide and cyanide. Class D2 includes asbestos and mercury. Class D3 is for biohazards, such as salmonella, HIV or Hepatitis B.

Class E is for disinfectants and cleaners. The WHMIS Class F Reactive – benzoyl peroxide and epoxy resins – might cause fumes or explosions when mixed with water.

“WHMIS Symbols”

In order to make it easier for workers, police officers and doctors to identify the contents of a box, pictures are used. These WHMIS Symbols are generally black-and-white circles with different images, such as test tubes, flames or skull-and-cross-bones.

“Which Industries Need WHMIS Labels?”

The following industries should use the WHMIS: transportation, semiconductor, industrial, warehouse, cleaning, aerospace and health care. The companies can use the WHMIS classification for training purposes. If workers see one class, then they should get in the habit of treating it in the approved fashion.

Storage should be at the proper temperature, humidity and pressure levels. Some reactive chemicals should not be stored with one another. Many hazardous chemicals with WHMIS labels should not be stacked. These could fall to the ground, leading to a spill or explosion.

This WHMIS Hazard Class Guide can help workers select protective clothing – glasses, gloves and overalls. Emergency responders can use the WHMIS safety labels for first-aid and fire control. For more information, ICC Compliance Center may be a good place to gather additional resources.

Jordan

Nowadays, sheet metal fabrication has taken roofing to another standard. The typical asphalt shingles have been replaced by metal shingles which are more durable. The latter comes in different types of material depending on your budget and preference. One of the best metal roofs is that made of steel shingles because they are strong and not very heavy.

The Steps of Installing Steel Shingles

  • Gather the Necessary Materials and Equipment

Ensure that you have the correct number of tiles required for the roofing. The number can be derived at by dividing the area of the roof with the area of one tile (100cm. You should also have a well aerated synthetic membrane that will be used as roof underlayment. Galvanized nails are very necessary for supporting the roof because they don’t corrode. You will also need equipment such as a hammer, ladder, and saw, among others.

  • Prepare a Flat Surface Where the Tiles Will Lie

The surface should not have large spaces between it so that the stability of the roof will not be compromised. The cover can be made of plywood or wooden boards. The surface should be well leveled to enable the tiles to interlock correctly.

  • Put an Underlayment (A Synthetic Material)

This will allow the circulation of air in and out of the roof. Lay an underlayment at the lower edge of the roof that will protect the roof from ice and water leakages. Start spreading the underlayment from the bottom edge of the roof and support it from its start with galvanized nails. The nails should be 8-inch apart. Spread the next row in an overlapping manner with the previous row by six inches.

  • Install the Tiles

Start installing the tiles along the lower edge of the roof. Then put shingles on the sides of the roof. Align and nail the tiles with the galvanized capped nails in overlapping rows until the entire roof is covered. Make sure that the tiles overlap by six inches in consecutive rows from the bottom of the roof.

  • Apply Impervious Material between Tile Joints

The material helps to prevent water leakage into the roof. The process is referred to as flashing and it should be done on the top, below and on the sides of the tiles. Also, flush around vents and pipes.

  • Instal Ridge Caps

Finally, you need to give your roof a beautiful finish by installing ridge cap tiles that cover the joints where the planes of the roof meet.

You see how uncomplicated it is to install steel shingles? Get a long-lasting roof that you can install at a very low or no labor cost. Change your roof or construct your new house using metal shingles and say goodbye to roof leakages.The Heather & Little Limited website is a useful resource if you would like to learn more information.

Jordan

The difference between starting a business and thinking about starting a business is basic; thinking is so much harder. In particular, starting a business that offers excellent commercial cleaning services is a seemingly impossible task. This is in a hypothetical scenario, however; one that includes the thought process only with the exclusion of the execution part. Setting up an office cleaning business has never been easy but will never be as hard as people like to think.
The intricacies of the office cleaning business
1. Doing a survey
There is no need to do any survey. Regardless of whether you are in a city, town or local municipality, there are plenty of offices that desperately need your services and don’t know it. Show up at their doors and they will beg you to step in.
2. Determine what services to offer
Depending on what amount of capital is at your disposal and what skills you can access, decide what services your enterprise will offer. A full range of services will include mopping and vacuuming, dusting and disinfecting, restroom cleaning, and trash removal. All the services will require particular instruments and gadgets. Hence, whatever resource is available will determine the scope of services you have to offer.
A good franchise, nonetheless, will offer all services that an office will need to get cleaned up. It will dust and clean all surfaces and equipment. It will sanitize and disinfect the office and the restrooms, vacuum all corners of the establishment and dispose of all the trash sustainably.
However, this business is a lucrative path that has not been well followed and is very promising. With a properly drafted business plan, no bank would deny you a loan. Therefore, you should not have an excuse to exclude certain services in your business.
3. Create a business plan

Of course, this goes without saying.
4. Getting all the necessary documents
The intricacies of starting an office cleaning business all fall here. There are a few documents that all franchise offering commercial cleaning services must have. These are:
• A license
• Registration documents
• Liability insurance
• Approved hourly rates charge shit
• Tax forms and W9 forms
5. Get down to marketing
Marketing is an essential part of starting a commercial cleaning franchise. Any elaborate action or word coined up towards the result of potential clients knowing of the existence of your services counts as marketing.
You should strive to make sure those potential customers;
• Know your services exist
• Prefer your services to those of the competition
• Know how to contact you
• Prefer your rates to those of your competition
• Feel confident in your capacity to meet their requirement
• Feel safe and secure when your stuff has access to their office particulars

Finally, as business peaks, you can draft up contracts to hire services of sub-contract employees that your franchise will occasionally call upon to offer their services on a need-to-indulge basis. For more information, please check out the Jan-Pro Cleaning Systems website.

Jordan

Proper flex storage solutions are very critical in ensuring the durability and efficiency in your flexographic printing services. This calls for proper cleaning, handling them with care and storing them properly. There are some procedures that can be followed to ensure flex storage solutions keep the sleeves in a perfect working state for a very long.

Handling with Care

It is imperative that all the flexographic sleeves are handled with care right from the storage to production and to ensure there is no damage. It would be an excellent idea to invest in flexcart to protect the sleeves from any damage. The flexcart will also guarantee the safety of employees if several sleeves have to be transported all at once. Caution should be observed particularly on sharp objects, and if there is any need to cut the sleeves, then a sharp knife need to be used with slight pressure to avert any damage.

Cleaning

Flexographic printing is often a dirty job, and the sleeves have to be kept clean if they are to print clean line. Therefore, cleaning has to be done as quickly as possible to remove any residues of inks, oil, tape and lubricants. Close attention needs to be observed to ensure the ends and the insides of the sleeves are always clean. Investing on sleeve cleaning cart that comes with a flexstand will ensure a quick cleaning of all the flexographic sleeves within the printing press without moving them out.

Flex Cleaning Solutions

Using the right cleaning products is crucial in the maintenance of the sleeves and harsh solvents should never be used in the cleaning process because it can damage the surfaces of the sleeves. Acids, salt solutions, or alkaline solutions should never be used in the cleaning process always refer to the recommendations from the supplier for the right cleaning products for your sleeves. Whenever the sleeves are not in use, it is advisable to store them in their protective covers to avoid damage. Sleeves should not be kept under the covers when they are wet, and they should be allowed to dry, and a compressed air dryer may be used to ensure they are dry and without any oil residues.

Storing

The horizontal storage system is not advisable because the sleeves will turn oval and are likely to cause injuries to workers if they fall especially if they were stacked so high. Against this backdrop, the storage of sleeves needs to be changed to vertical sleeve storage system. The vertical system can store more sleeves in a small area and much easier to retrieve them whenever they are needed. A flex stand that has adjustable discs and rubber pads will make an ideal vertical storage system that will ensure the longevity of your flexographic sleeves and minimize printing costs in the long run.

Jordan

The Canadian government, through comprehensive research and analysis, has in recent times determined that the major problems facing small businesses within its boarder mostly include insufficiency of funds. It thus, through the help of self-help groups like Self-Help Credit Union decided to set an initiative to offer small businesses with:
1. Capital investment funding
2. Hiring and training grants
3. Research and Development Funding
4. Business expansion funding grants and loans
To make sure that the funds would be made use of appropriately, sustainably and profitably in a way that improved living standards of the people and strengthen the Canadian economy by bridging the gap between the rich and the poor, checks and balances for using the government grants for small businesses. Four programs were set up with specific and unique eligibility criteria. The most inspiring of all small business grants Ontario success stories is the Durham Foods growth and renaissance in Pease pudding appreciation.
Humble beginnings

The Durham Food hub started as a mobile truck food store. The mobile kitchen, in the beginning, sold sausage sandwiches made from pasture-raised pigs raised on nearby farms. The co-owners, Tina Prevatte and Jennifer Curtis used all the avenues they could to grow their businesses. These avenues included government grants for small businesses, relationships with creditors and trial-and-error. They endeavored to serve as the middlemen in the livestock product processing system. They used the funds to buy whole animals from small-time ranchers and transport them to restaurants, grocery stores and institutions.
Taking the unexpected turn
Ingenious decisions by Tina Prevatte and Jennifer Curtis propelled Durham Foods into unexpected heights. Durham Foods did not grow into a big restaurant or a itinerant brand. Instead, it exploited the gaping loops in the food market of product. They began connecting farmers to buyers in search of local beef and pork grown naturally on pastures without genetically modified hormones, animal by-products or antibiotics.
Another wave these inspiring entrepreneurs rode on was the abrupt renaissance in Pease pudding appreciation. The Pease pudding had initially been a staple food for majority households in the North East but a spontaneous spread of the appreciation for the delicious but low fat and zero gluten delicacy transpired. Durham Food was there to facilitate the renaissance by making sure the delicacy reached outer regions of the North East.
Taking advantage

Small business owners should take advantage of whatever programs their businesses quality for in this government grants. The process is easy as bureaucracy is minimized. The grants are evidently changing lives and improving the quality of life for many Canadians in Ontario.

Jordan

Some companies set their alarm monitoring system right before they leave work for the day; however, choosing a system that has at least some features that can be activated, even when employees are in the building, is pivotal to the safety of the staff.

 

Early Morning Hours

When the sun is just starting to appear at the horizon and the air has a slight chill, even on the warmest days, you may feel a sense of tranquility with the world. While that peace is more than just a chimera, it also isn’t inviolable. Employees who are entering the facility, especially by themselves, may be at risk for an attack. In fact, some criminals may target businesses at these hours because they know how empty the spaces are. An alarm system with a panic button can help to keep employees safe.

 

Work Day

Keeping an alarm system on fully throughout the work day is likely impossible for most companies as both employees and clients are continually walking in and out of the door. At small businesses, however, arming the system might be possible, and staff may need to take this action if the business is located in a high crime area or if companies in the area have been targeted recently. Even for businesses where this plan is an impossibility, they can keep certain features of the alarm system armed. For example, no reason exists as to why they cannot use the smoke, fire, carbon monoxide and natural gas detectors. Also, people can have access to panic buttons in the event of an emergency.

 

At Night

While statistics will vary depending on a variety of factors, such as location, break-ins may very well be more likely after the business has closed up for the night. Criminals know that no one is there. Furthermore, disgruntled ex-employees might use this time to take out their hostilities toward the business. Even if no one breaks in to the premises, a fire or carbon monoxide or gas leak could wreak havoc on the business. Properly functioning alarm monitoring can help to potentially end the problem before it gets worse.

 

Off-times

At points, the entire business may close down for a particular stretch of time. Maybe the company is on holiday, or perhaps the business is moving to a new location soon. If criminals see that the business lies unoccupied for a number of days in a row, they may decide that this time is the perfect one to strike.

Alarm monitoring is not something you should pay only a minuscule amount of attention to. Instead, a proper alarm can work to keep you and your employees safe at all times.

Jordan